Pentair C1, 155002-43 Replacement for AquaFlo ICP-10-10 Pleated Carbon Impregnated Polyester

The Pentair C1, 155002-43 Replacement for AquaFlo ICP-10-10 Pleated Carbon Impregnated Polyester is a replacement water filter cartridge measuring 10 inches in length and 2.5 inches in diameter. This 10" filter features impregnated polyester media and a 10 micron rating for the reduction of the taste and odor of chlorine in your water.

Specifications:

• Brand: Pentair
• Model Number: C1
• Part Number: 155002-43
• UPC Number: 051678002438
• Replaces Part Number: ICP-10-10
• Pack Size: 1
• Filter Life: 3 Months (2,500 Gallons)
• Dimensions: 9-3/4" x 2-1/2" (2-5/8" with end-caps)
• Filter Media: PAC Impregnated Cellulose
• Micron Rating: 5
• Flow Rate: 5 gpm
• Temp Range: 40 - 125° F
• NSF Certification(s): 42

Additional Features:

• End Caps: Vinyl Plastisol
• Netting: Polyethylene
• Core: Polypropylene
• Reinforcement Backing: Cellulose Polyester
• High dirt-holding capacity
• Recommended for chlorinated water supplies
• Warning: For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Not recommended with well water.
• Note: Some harmless bacteria will attack cellulose media cartridges. If your cartridge seems to disintegrate, or has a musty or moldy odor, switch to a synthetic media cartridge or consult the manufacturer.

How do you install the Pentair C1, 155002-43 Replacement for AquaFlo ICP-10-10?

1. Turn off water supply. Press red pressure-relief button (if present).
2. Unscrew housing. Remove large o-ring, wipe clean and set aside.
3. Discard used Pentair C1, 155002-43 Replacement for AquaFlo ICP-10-10 filter cartridge. Wash housing with dish soap and warm water using a nonabrasive sponge or cloth. Rinse thoroughly.
4. Fill 1/3 with water. Add about 1 tablespoon of bleach and scrub to disinfect. Rinse thoroughly.
5. Lubricate o-ring with clean silicone grease. Change o-ring if any damage cuts or degradation are present. Insert o-ring in groove.
6. NOTE: This step is important to ensure a proper housing seal. Make certain the o-ring is seated level in the groove.
7. Insert new Pentair C1, 155002-43 Replacement for AquaFlo ICP-10-10 filter cartridge.
8. Screw housing onto the cap and hand-tighten. Do not over tighten. Make sure cap standpipe slips into cartridge.
9. Turn on water supply. Press pressure-relief button (if present). Check for leaks before leaving installation.

How often should you replace the Pentair C1, 155002-43 Replacement for AquaFlo ICP-10-10?

• Changing your Pentair C1, 155002-43 Replacement for AquaFlo ICP-10-10 is a very quick and easy process that should be done once every three months.

What contaminants does the Pentair C1, 155002-43 Replacement for AquaFlo ICP-10-10 reduce?

• The Pentair C1, 155002-43 Replacement for AquaFlo ICP-10-10 is NSF 42 certified, which means that it reduces the following contaminants:

  • Chlorine Taste and Odor Reduction

Resources:

• View the Pentek C1 Product Specification Sheet